![]() |
![]() |
Fuel Injection |
Post Reply ![]() |
Page <12 |
Author | |
micjen ![]() Member ![]() ![]() Joined: 12 July 2014 Location: Brisbane Qld Status: Offline Points: 164 |
![]() ![]() ![]() ![]() ![]() |
I would be using a magnetic breaker type electronic ignition conversion on the existing dizzy. Fixed, then I would run it through the computer for advance purposes. For that matter don't even need a crank angle. The original dizzy will do.
Microtech (or Wolf 2D etc) which you will have ready access to in NZ will have the appropriate setup depending on what pieces you use. Throttle body injection doesn't rely on group or sequential fire unlike multipoint injection so keeps the sensors much simpler (and fuel pump setup also.!!) RPM (from coil) and manifold vacuum (load) plus a simple throttle position switch (on/off) is all that is required. Can get fancy and put in oxygen sensor, speed sensor and use 3D laptop programming but I don't think thats necessary. A good run up on a dyno using a knowledgeable person will give all that is needed to tune it. Or others simply raid the entire setup off an EA Falcon (which will be in profusion in NZ wrecking yards) with throttle body injection. Wiring, computer the lot. Don't need ignition control so makes it simpler. |
|
CJ2A rebuilder. Let the Willys Jeep live again.
|
|
![]() |
|
micjen ![]() Member ![]() ![]() Joined: 12 July 2014 Location: Brisbane Qld Status: Offline Points: 164 |
![]() ![]() ![]() ![]() ![]() |
This is actual measurements of a L/F134 conrod minus the slot and designed for interference fit using the original pistons gudgeon pins and bearings. No more pinch bolt or designed in weakness. i am waiting on the actual set now.
|
|
CJ2A rebuilder. Let the Willys Jeep live again.
|
|
![]() |
|
mrlentle ![]() Member ![]() Joined: 10 Aug. 2014 Location: New Zealand Status: Offline Points: 2 |
![]() ![]() ![]() ![]() ![]() |
Is this still coming together or?
|
|
http://willysm38build.blogspot.co.nz/
|
|
![]() |
|
Doodledad ![]() Member ![]() ![]() Joined: 08 Mar. 2016 Location: Muncy Pa Status: Offline Points: 400 |
![]() ![]() ![]() ![]() ![]() |
Just wondering what ever became of this project?
|
|
46 2A 29938 (unrestored driver)
51 3A "Wilma" 55 3B Fountain 47 2A Yard Art 97 XJ “Lafaunduh” 00 TJ RockCrawler "Hooker" 13 Rubicon JKU "Alice" 48 C2A Eileen 00 TJ frame off resto “Stacy” |
|
![]() |
|
beentheredonethat ![]() Member ![]() ![]() Joined: 22 Dec. 2018 Location: TN, USA Status: Offline Points: 1 |
![]() ![]() ![]() ![]() ![]() |
Hello, New to the Forum and very interested in your build. Particularly the billet rods and forged pistons. I am unable to find a source in the states for these items. Currently I am looking for another Flat Fender project and have long toyed with the idea of coaxing a bit more power out of the L-head. I have been running around in these things since I was a kid in the 60's. Also, are you able to find the Willy Willy head or the Hickey head? Thanks
|
|
47 Willys,Stage1 455, Indian 111
|
|
![]() |
|
Ol' Unreliable ![]() Member ![]() ![]() Joined: 25 Sep. 2016 Location: CO Springs CO Status: Offline Points: 4226 |
![]() ![]() ![]() ![]() ![]() |
Welcome to the page, beentheredonethat! Lots of us have been wondering for 4 years what's become of this project.
|
|
There's a reason it's called Ol' Unreliable
|
|
![]() |
|
Doodledad ![]() Member ![]() ![]() Joined: 08 Mar. 2016 Location: Muncy Pa Status: Offline Points: 400 |
![]() ![]() ![]() ![]() ![]() |
I would LOVE to get my hands on a Willy Willy head.... just to set on the shelf!
|
|
46 2A 29938 (unrestored driver)
51 3A "Wilma" 55 3B Fountain 47 2A Yard Art 97 XJ “Lafaunduh” 00 TJ RockCrawler "Hooker" 13 Rubicon JKU "Alice" 48 C2A Eileen 00 TJ frame off resto “Stacy” |
|
![]() |
|
Greaser007 ![]() Member ![]() ![]() Joined: 16 Jan. 2018 Location: Anderson, Calif Status: Offline Points: 850 |
![]() ![]() ![]() ![]() ![]() |
I just read through this once again.
I like those Conrods for higher highway rpm. but I cannot afford them. And, I have been tossing around in my mind of using the throttle body off of an '89 Honda Civic engine and grafting it over to my L134 engine. I am just too busy with other projects to even look through the local Pick-n-Pull yard for a Donor vehicle with a Throttle-Body unit. Get this: Rochester makes the factory fuel injection for the 3.2L Isuzu V-6 multiport injection. So, that tells me that the individual auto mfr's do not make their own fuel injection, it is "sourced-out" to the major mfr's. I wonder who made the OZ unit that was shown on the thread start ? I am going to have to go snooping around the small autos for a throttle body and engine control system. :) The challenge may be to 'perfect' the location of the O2-sensor for proper sensing which will require a good analyzer to read fuel-air ratios and block temp sensor operation. Many things to adjust once the system is in place. oh, you were going to set your idle speed ? nope, the ecm controls it on most throttle bodies with a TPS. Did you digest your TPS report today ? hahaha you got the memo right ! Just teasing, but the more I delve into working on fuel injected auto engines, the are really pretty basic. The TPS (throttle position sensor) tells the ecm to hold the injector's open longer for acceleration with throttle butterfly open. All good stuff. Now, I need to get a handle on the newer O2 sensors which have a variable reading rather than a fixed reading. My brain is getting flooded with trying to digest so much information that is shared here on the forums, that I had better end this dissertation, and move on to another sector thread. There is one nice thing about fuel injection - Instant Start-up. Len |
|
![]() |
|
Doodledad ![]() Member ![]() ![]() Joined: 08 Mar. 2016 Location: Muncy Pa Status: Offline Points: 400 |
![]() ![]() ![]() ![]() ![]() |
My TBI is based off of the GM TBI found on 87-95 GM Trucks. It uses a MAP,O2,CTS and ESC and on the TBI a IAC and TPS to regulate fuel and timing. The distributor was fitted with a Hall effect to advance the timing as needed. The set up works well. I’m not sure what kind of support you would be able to have with other factory take offs from foreign cars. There’s many people that can send you chips with the data you collect to dial-in a TBI on your L134. Very inexpensive and very easy to find parts for these fuel injection set ups.
|
|
46 2A 29938 (unrestored driver)
51 3A "Wilma" 55 3B Fountain 47 2A Yard Art 97 XJ “Lafaunduh” 00 TJ RockCrawler "Hooker" 13 Rubicon JKU "Alice" 48 C2A Eileen 00 TJ frame off resto “Stacy” |
|
![]() |
Post Reply ![]() |
Page <12 |
Tweet |
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |