Trailer ID anyone? |
Post Reply | Page <12 |
Author | |
ndrtkr
Member Sponsor Member Joined: 18 Mar. 2009 Location: Mississippi Status: Offline Points: 884 |
Post Options
Thanks(0)
|
There are no corner grab handles Paul. I still say Willys MBT.
|
|
"Life is tough, it's even tougher if you're stupid"- John Wayne
|
|
hillbilly21
Member Sponsor Member Joined: 18 June 2006 Location: USA Status: Offline Points: 4964 |
Post Options
Thanks(0)
|
MY BAD...
|
|
Ryan_M
Member Sponsor Member Joined: 03 Jan. 2012 Location: Glenburn, ME Status: Offline Points: 636 |
Post Options
Thanks(0)
|
I spent the afternoon lying on the garage floor inhaling lead paint dust.....and then I decided to work on the trailer . Here are a few more pics and a little more info:
1) Data Plate: If yours is present, what is the info stamped on it? How many "fields" are available for stamping info? No data plate 2) USA Number: Wet sand an upper corner area to see how many coats of paint are on the rear panel. Then SLOWLY wet sand right under the rear top hook to find the "USA", in doing that you will now know what to look for when you sand just above the lower frame rail looking for the eight numbers usually found on the rear panel...you may find White or Blue paint used here. Rear panel not present 3) ACM Number: American Central MFG. made the tub/frame assembly. They put a number on the gusset plate under the left front spring hanger so remove it and wire-wheel the gusset looking for numbers about 7/16" in height. You may find a "B" or "W" in front, behind or below the number. W 4011 4) Upper Shock Mount: Is it threaded or cotter-pin type? Is it RIVETED or BOLTED to the frame? Cotter Pin, Bolted to frame Is the LOWER shock mount threaded or cotter-pin? Cotter Pin 5) Is the axel a straight tube, with a welded seam in the middle or does it have a center cast section? Has center cast section which is stamped "3" 6) Springs: How many leaves in the springs? Eight or ten? Standard FLAT Willys type or a flattened "U" shape? Are the spring clips with the closure on the top or the bottom? 8 leaves. I think they are U shaped. They are flat but the bottom edges are beveled. Is that a "U"? 7) Taillights & Reflectors: What is the mfg of the taillight buckets and doors? Can't find any marking on the buckets. The smaller light in each one is marked "ARROW, USA, MEDFORD NJ". What about the reflector bezels? Bezels stamped "BROWN" and "No 100 CIN". Lens are "GROTELITE" Check to see if the reflectors have the bolt HEADS inside the tub. See if they have any lead washers on them. Yes, lead washers are present Taillight Mounts: Standard "L" brackets bolted to the tub or welded on? Drivers side welded, passenger side bolted. I think it was originally welded though. 9) Numbers: Look on the top or sides of the drawbars, check the edge of the front of the tub where the handbrake is bolted and look on the left side of the frame near the front of the trailer frame. Any numbers stamped there? Couldn't find anything but not exactly sure where to look and any markings could be covered by multiple coats of paint. 10) Bolts: Check the markings (if any) on the bolt heads on the fenders or other bolts on the trailer. (A, AA, EC, BC or others or none?) Fender bolt heads marked "A" 11) Unit Numbers: Most outfits did NOT mark the rear frame beneath the tub with the unit info but some did. Wet sand this area carefully also, there may be several coats of paint and several units markings! Did not sand to try and find these numbers. Edited by Ryan_M - 03 May 2012 at 12:08am |
|
Ryan_M
Member Sponsor Member Joined: 03 Jan. 2012 Location: Glenburn, ME Status: Offline Points: 636 |
Post Options
Thanks(0)
|
Here's an e-mail directly from Chuck Lutz. Looks like it is very likely a '42 Willys MB-T. Thanks to Chuck (and everyone else who replied here) for the info.
Hi Ryan…
That Willys MB-T has a pretty cool tailgate from a later CJ jeep adapted to it!
It is a very early Willys ¼ ton but I don’t have any others with an ACM number close to yours that has a data plate to cross reference with so this is a pretty GOOD estimate. While you are doing the restoration on this trailer I may get some additional info to tighten up the estimate so I suggest you get back in tough with me on this one at that time to see I can improve the estimates for you!
For now….
Willys MB-T Serial Number: 3467 DOD: 8-42 USA Number: 0160336
Best Regards, Chuck Lutz Edited by Ryan_M - 04 May 2012 at 9:23pm |
|
48cj2a
Bantam Trailer Moderator Sponsor Member Joined: 22 July 2005 Location: Central, IL Status: Offline Points: 4523 |
Post Options
Thanks(0)
|
Chuck's the man on these military MBTs and T3s if you can give him an ACMor USA number
|
|
Art C USAF (Retired)
47 CJ2A #134955 Project 48 CJ2A #206759 62 L6226 Station Wagon #58167 10900 45 T3-C #191 Project http://www.bantamt3c.com http://www.48cj2a.com |
|
FLYINGFISH
Member Joined: 29 Oct. 2012 Location: South Africa Status: Offline Points: 27 |
Post Options
Thanks(0)
|
|
|
FLYINGFISH
"If in doubt, ask" |
|
FLYINGFISH
Member Joined: 29 Oct. 2012 Location: South Africa Status: Offline Points: 27 |
Post Options
Thanks(0)
|
Hello Ryan_M
I have been looking for a good sample of an unusual trailer and yours meets my requirements just perfectly. If you don't mind I would like to base my 1/2 Scale build on yours. This will go perfectly with my 1/2 Scale CJ-2A (Project. http://www.thecj2apage.com/forums/1-2-scale-cj2a-project_topic26456.html) Best regards, Marc & Jarred.
|
|
FLYINGFISH
"If in doubt, ask" |
|
Ryan_M
Member Sponsor Member Joined: 03 Jan. 2012 Location: Glenburn, ME Status: Offline Points: 636 |
Post Options
Thanks(0)
|
I'd be honored. Let me know if you would like any additional photos or measurements.
|
|
Estendog
Member Joined: 09 July 2018 Location: Netherlands Status: Offline Points: 3 |
Post Options
Thanks(0)
|
Hi Marc & Jarred,
Here from Holland.. I am also searching the internet for drawings with sizes.
but do not continue until I have logged in on this website and I come across your project and am very impressed by your jeep. so please be able to receive drawings from you. thank you very much. photos will follow when I start ... greets, Gregory |
|
Post Reply | Page <12 |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |